vmnic0 link down after enable link aggregation
Hello everybody.I just connected a new host (HP DL360G9, ESXi 6.5 build 5224529, 4xGigabitEthernet) with new Cisco SG500 Switch and trying to configure link aggregation, but something go wrong. The...
View ArticleRe: vmnic0 link down after enable link aggregation
Try to follow the procedure described in this KB: NIC teaming using EtherChannel leads to intermittent network connectivity in ESXi (1022751) | VMware KBand set PortFast on the ESXi facing ports STP...
View ArticleRe: vmnic0 link down after enable link aggregation
Yes, i have read already this KBs. Finally i found the source of problem - it`s a new ntg3 driver. After I doesxcfg-module -e tg3esxcfg-module -d ntg3rebooteverything is good - no more failed uplinks....
View ArticleRe: DR Testing - Multi-Host Bubble Networks
Thanks very much Bayu. Appreciate the information.
View ArticleCan you move ESXi Hosts with distributed switches from one vCenter to another?
Hi, Can you move ESXi Hosts with distributed switches from one vCenter to another? I know you couldn't under previous versions of ESXi but I assume that has changed now. We do it all the time with...
View ArticleRe: Can you move ESXi Hosts with distributed switches from one vCenter to...
The supported way is to migrate to vSS, move to other vCenter, then migrate to vDS as per this KB: Moving an ESX/ESXi host with vDS from one vCenter Server to another (1029498) | VMware KB You can...
View ArticleRe: Can you move ESXi Hosts with distributed switches from one vCenter to...
dvs's are a pain to support compared to the standard vswitch!! Unless you have an extremely large environment to support I see no benefit in them.
View ArticleRe: Can you move ESXi Hosts with distributed switches from one vCenter to...
there are also some features that only available in vDS such as Network I/O Control, Load Based Teaming/Route based on Physical NIC Load, LACP, etc some product/software integration such as VMware NSX...
View ArticleClik here to view.
Qlogic QLE8262 not presenting as storage adapter after 6u3 upgrade.
I was recently asked to assist with an in place upgrade of our ESXi5.5u2 hosts 6u3. The hosts are Dell r720s. The ISO was VMware-VMvisor-Installer-6.0.0.update03-5050593.x86_64-Dell_Customized-A00. The...
View Articleusing Standard vSwitchs, vLan, vMotion and HA
Hello, I m trying to understand the practical use of Standard vSwitchs and how I can get to create vLAN and still be able to perform vMotion and HA. I am using vSphere Enterprise 6, with 2 hosts linked...
View ArticleRe: using Standard vSwitchs, vLan, vMotion and HA
once again the mistake was between the chair and the desk.One should keep simple and stay with short names and moreover IDENTICAL names between hosts. Stupid space included in one host and not the other.
View ArticleTraffic Flow in Nested VM
Hello Can anyone plz explain how does a packet flow in a Nested Cloud Environment? Thanks
View ArticleRe: Qlogic QLE8262 not presenting as storage adapter after 6u3 upgrade.
So, this turned out to be a bad driver from the upgrade. I had tickets open with Dell, QLogic, and VMware. Dell claimed the card was good at the hardware level and so we should talk to QLogic. QLogic...
View ArticleUnable to vMotion between hosts
Hi there!I'm trying to vMotion VMs between an old cluster (vsphere 5.5 / dvSwitchs 5.5) to another one (vsphere 6.5 / dvswitch 6.5).I'm using vCSA 6.5 Flash mode. It gives me the errors: "Change the...
View Article“Currently connected network interface ‘Network adapter 1’ uses network...
I am new in VMware. I have 2 Esxi Server added in HA cluster. There are two virtual machines one is XPVM another is XPVM2 both are in Esxi1. High availability is working fine when both XPVMs are...
View ArticleRe: “Currently connected network interface ‘Network adapter 1’ uses network...
The XPVM works because it is connected to "VM Network" port group which is present on ESXi1 and ESXi2, and XPVM2 fails because it is connected to "VM Network2" port group which is present only on ESXi1...
View ArticleRe: “Currently connected network interface ‘Network adapter 1’ uses network...
Thank you very much. I had sleep lees night before your reply. I create a same port group in both Esxi Servers named "VM Network5" as VM Network2 was creating confusion in my mind. After following your...
View ArticleMigrate an Existing Virtual Adapter between vSphere Distributed Switches
We are in the process of Migrating our 5.5 esxi hosts and vCenter 5.5 from 1Gb Nics to 10Gb Nics. We currently have Two Distributed Switches, one which is has two 1Gb Nics which has a MGT port group...
View ArticleRe: network portgroup problem
Probably a bit late to help you, but I ran into the same problem after adding a VMKernel NIC to the portgroup in question. Despite the message, the VM that was apparently 'broken' was still able to use...
View ArticleCan not Ping Secondary Ip in VM Created By ESXI 5.1
Hi All, Maybe my question is so easy but I don't know how to do because I'm newbie at ESXI. I'm using ESXI 5.1 I have two different ip in two different block(192.168.2.48 & 10.122.127.203). I have...
View Article
